蒙阴五粮家用酿酒设备
酿酒设备|白酒酿酒设备|生料酒曲的生产|传授生料酿酒技术销售

　　抛光，就是将不锈钢的表面进行特殊化的处理，使之看起来更加的光滑，能够使酒罐达到一致的平整度，这样无论是从卖相上来说还是从实用性上来说，都要上一个层次。抛光的工艺我们已经有所了解了，但是具体的做法是怎样的呢?白酒酿酒设备在使用时其最大的特点就是不生锈，其实其不生锈也是相对的，若长时间受外界环境的影响和一些人们因素，其表面也会被氧化，从而造成设备的生锈影响正常使用，因此为了使其能够更好的为我们服务，我们需要对其进行抛光处理。

　　Polishing, is specialized for processing the surface of the stainless steel, so it looks more smooth, can make the wine can reach the smoothness of the same, so whether it is from the appearance it is from the practical view, should be on a level. Polishing process we already know, but the specific practice is what kind of? In the use of liquor brewing equipment the biggest advantage is that it does not rust, in fact it does not rust is relative, if long time affected by the external environment factors and some people, the surface will be oxidized, resulting in equipment the rust of normal use, so in order to enable it to serve us better, we need to carry on the polishing treatment.

　　白酒酿酒设备的表面抛光步骤：

　　Surface polishing steps for liquor making equipment:

　　1、粗磨，用600#的砂带在三面上往返磨削工件，本工序要达到的目标是去掉工件焊接留下的焊点，以及在上步工序出现的碰伤，达到焊口圆角初步成型，水平面和垂直面基本无大划痕，无碰伤，经此步工序后工件表面的粗糙度应能达到R0.8mm。注意在抛光过程中注意砂带机的倾斜角度和控制好砂带机对工件的压力。一般来说以与被抛面成一条直线比较适中!

　　1, coarse grinding, and grinding the workpiece on the three side with the 600# belt, the process to achieve the goal is to remove the solder welding left, and bumps appear in the process step, to weld fillet shape, horizontal and vertical surface with no scratches, no scratches, after this step after the workpiece surface roughness can reach R0.8mm. Attention should be paid to the tilt angle of the belt conveyor and the pressure of the belt conveyor on the workpiece during the polishing process. Generally speaking, it is more reasonable to make a straight line with the thrown face

　　2、半精磨，用800#的砂带按照前面往返磨削工件的方法中磨工件的三面，主要是对前面工序出现的接缝进行修正以及对粗磨后产生的印痕进行进一步的细磨，对前面工序留下的印痕要反复磨削，达到工件表面无划痕，基本变亮。本工序表面粗糙度应能达到R0.4mm。(注意本工序不要产生新的划痕及碰伤，因为在后面的工序无法修补此类缺陷。)

　　2, semi fine grinding, grinding method with 800# belt in front of round-trip grinding in three, mainly on the previous process of joint of the correction and the coarse grinding marks for further fine grinding, leaving marks to the previous process repeated grinding, no scratches to the surface of the workpiece, basic light. The surface roughness of this process should be up to R0.4mm. (note that new scratches and bumps are not allowed in this process because the defects cannot be repaired in the subsequent process. )

　　3、精磨，用1000#的砂带主要是对前步工序出现的细小纹线的修正磨削，磨削方法与上同。本工序要达到的目标是磨削部分与工件未磨削部分的接缝基本消失，工件表面进一步光亮，通过本工序磨削后的工件要基本接近镜面效果，工件表面粗糙度应能达到R0.1mm。

　　3, fine grinding, using 1000# abrasive belt, mainly for the front steps of the small lines of grinding, grinding, grinding method and the same. This procedure is to achieve the goal of grinding part and workpiece grinding part of the seam not disappeared, the surface of the workpiece through further light, the workpiece process after grinding to close to the mirror effect, the surface roughness of the workpiece should be able to reach R0.1mm.

　　白酒酿酒设备的表面抛光的注意事项：1、必须经专业培训人员方可使用。2、抛光中严禁长时间在某一处原地研磨，以免抛漏底漆。3、抛光过程中应及时清理研磨盘上的氧化层污垢及研磨剂等物，避免固化难处理及再抛光时划伤车漆。4、酒罐抛光需保持研磨盘的洁净，提高施工的效率。

　　Attention should be paid to the surface polishing of liquor making equipment: 1. It must be used by professional training staff. 2, polishing is prohibited for a long time in a place to avoid grinding, polishing paint leakage. 3, polishing process should be cleared in time on the grinding pad oxidation layer, dirt and abrasives and other things, to avoid curing, difficult to handle and polishing when scratching the car paint. 4, the wine tank polishing needs to maintain the grinding plate clean, enhances the construction efficiency.