蒙阴五粮家用酿酒设备
酿酒设备|白酒酿酒设备|生料酒曲的生产|传授生料酿酒技术销售

　　机械设备在使用过程中一定会因操作者的一些使用不当产生故障，当然白酒酿酒设备也不会幸免于难。但是，如果您能在设备出现故障时能迅速做出反映，立即解除故障，那么机可以防止意外事故的发生。接下来，就请酿酒设备厂家为大家简单的介绍，希望能对您有所帮助!在酿酒设备故障中最常见的应该是由于设备负荷超载导致的意外事故。负荷超载有可能是以下原因造成的：

　　Mechanical equipment in use in the course of some operators will be due to improper use of failure, of course, liquor, brewing equipment will not survive. However, if you can make a quick response when the equipment fails, and immediately remove the fault, then the machine can prevent accidents. Next, please make wine equipment manufacturers for everyone simple introduction, hope to be helpful to you, in the brewing equipment failure, the most common should be due to equipment overload caused by accidents. Overload may be caused by the following reasons:

　　1、温控仪表失灵或者热电偶没有插好，造成聚合物加工温度过低，引起负荷超载。

　　1, temperature control instrument failure or thermocouple is not inserted, resulting in polymer processing temperature is too low, causing overloading of the load.

　　2、突然更换原料牌号或者工艺配方，工艺条件没有及时调整，造成负荷超载。

　　2, suddenly change raw material brand or process formula, process conditions are not adjusted in time, resulting in overload.

　　3、口模、螺杆设计不合理，造成口模压力过高。

　　3, the die and screw design is unreasonable, resulting in excessive pressure on the die.

　　4、滤板或者过滤网堵塞。这种情况在挤出用劣质无机物填充的材料或者大量使用不洁净的回收料时，会经常发生。

　　4, filter plate or filter block. This often occurs when extruded materials filled with inferior inorganic materials or a large amount of recycled material are used.

　　5、异物进人机筒会引起负荷超载。比如，较大的铜制品进入机筒，虽然没有造成螺杆、机筒损坏，但是可能引起负荷超载。

　　5, foreign objects into the machine cylinder will cause overload. For example, larger copper products into the barrel, although not caused by screw, cylinder damage, but may cause overload.

　　当酿酒设备出现故障时应按照以下方法修理：切断电源和水源，拆卸机头进行清理后，拆下螺杆和机筒并立即清理。如果不是螺杆损坏，应该将清理好的螺杆涂抹油脂垂直悬挂起来。这时再分析发生事故的原因和部位，并根据该部位的图样安排拆卸工作并准备备件。电动机或者轴承发生突然损坏，往往都是在定期维护保养时没有发现潜在的问题，没有及时进行更换。因此，只要换上新的备件或是在保养时及时发现问题并解决，一般就可以重新开机。酿酒设备的负荷超载故障往往伴随有熔体压力和电流的急剧升高。但是对于酿酒设备生产厂自己制造的减速箱，如果频繁发生传动轴、齿轮损坏事故，要考虑可能是减速箱加工精度的问题。

　　When brewing equipment failure, should be repaired according to the following methods: cut off the power supply and water source, remove the nose, after cleaning, remove the screw and barrel, and immediately clean up. If the screw is not damaged, the cleaned screw shall be coated and the grease will be hung vertically. Then analyze the cause and location of the accident and arrange the demolition work and prepare the spare parts according to the drawing of this part. Motor or bearing sudden damage, often in regular maintenance, found no potential problems, did not change in time. Therefore, as long as the new spare parts or maintenance in time to find problems and solve, you can generally re boot. The overload failure of brewing equipment is often accompanied by a dramatic increase in melt pressure and current. But for the reduction gearbox made by the brewery equipment factory, if the transmission shaft and gear damage occur frequently, it is necessary to consider the problem of the machining accuracy of the reduction case.